Biosafety cabinet certification: NSF/ANSI 49 field tests and acceptance criteria
Updated · 6 min read
On this page
A Class II biosafety cabinet (BSC) protects three things at once: the person working at it, the work on the tray and the room around it. Field certification is the check that it still does all three where it is installed, measured against NSF/ANSI 49 and the cabinet manufacturer's set points. This guide covers what a field certifier tests, the acceptance criteria most programs apply, and what usually explains a failure.
If you're not sure which type of cabinet you're looking at, start with biosafety cabinet classes and types.
It summarizes common practice; it is not a substitute for the standard. Certify to the edition your customer specifies and to the nominal values on the cabinet's data plate or manual.
When a cabinet needs certifying
- At installation, before the cabinet is put into use.
- At least once every 12 months after that.
- After it is moved, even within the same room.
- After a HEPA filter is replaced or internal parts are serviced (anything that opens the plenums or changes the motor or blower setting).
Cabinets used for sterile compounding under USP <797> or hazardous-drug compounding under USP <800> are on a six-month cycle instead. See how often each kind of unit needs certification.
The field tests at a glance
| Test | What it shows | Usual acceptance criterion |
|---|---|---|
| Downflow velocity | Air moving down onto the work surface protects the work and carries contamination away | Average within ±5 fpm of the manufacturer's nominal; each reading within ±20% or ±16 fpm of the average, whichever is greater |
| Inflow velocity | Air entering the front opening keeps aerosols in and protects the operator | Within ±5 fpm of the manufacturer's nominal (and never below the type minimum: 75 fpm for Type A1, 100 fpm for Types A2, B1 and B2) |
| Airflow smoke patterns | The air barrier at the opening works, visibly | Smoke moves down without dead spots or reflux; nothing escapes at the view screen, the edges of the work opening or the sash seals |
| HEPA filter leak | Supply and exhaust filters, and their seals, aren't leaking | No reading above 0.01% of the upstream challenge when scanning; filters that can't be scanned are probe-tested against a tighter limit (commonly 0.005%) |
| Site installation | The installation doesn't defeat the cabinet | Exhaust alarms work (canopy connections for Type A, hard ducts for Type B); placement away from doors, diffusers and traffic |
Many customers also ask for electrical safety, lighting, noise, vibration or UV lamp checks. These are worth recording, but they are not part of the core field certification.
Downflow velocity
Downflow is measured with a thermal anemometer at a grid of points in a horizontal plane above the work surface, using the grid the manufacturer specifies for that model. The plane is commonly 4 inches above the bottom edge of the sash frame. Two things are checked:
- The average must be within ±5 fpm of the nominal downflow on the data plate.
- Uniformity: every point must be within ±20% of the average, or ±16 fpm, whichever band is wider. A cabinet with a good average can still fail here if one corner is starved.
The biosafety cabinet airflow calculator does both checks on a pasted grid of readings.
Inflow velocity
Inflow is the operator-protection number, so it gets the most scrutiny. The preferred field method is the direct inflow measurement (DIM): a flow hood (capture hood) sealed over the front opening reads the volume of air coming in, and dividing that volume by the area of the work opening gives the average inflow velocity. Apply any correction factor the cabinet manufacturer publishes for your model of flow hood.
When a DIM isn't practical, use the alternative the manufacturer specifies for that cabinet, such as velocity readings through a restricted sash opening, and record which method you used. The result must be within ±5 fpm of the nominal inflow, and never below the minimum for the cabinet type.
Airflow smoke patterns
Smoke tests show what velocity numbers can't. The usual set is:
- Downflow: smoke released along the cabinet's centerline, above the work opening, moves smoothly down without dead spots or reflux (upward movement).
- View-screen retention: smoke run along the inside of the view screen stays in the cabinet.
- Work-opening edge retention: smoke run along the edges of the opening, outside the cabinet, is drawn in and doesn't escape.
- Sash and window seals: smoke along the seams of the sash shows no leakage out.
Record each one as acceptable or not. A cabinet with marginal inflow often fails at the edges first, especially near an open door or a supply diffuser.
HEPA filter leak test
An aerosol (commonly PAO) is introduced upstream of the filter and its concentration is measured with a photometer and set as the 100% reference. The downstream face of the filter and its perimeter seal are then scanned slowly with the photometer probe, in overlapping strokes close to the filter face. Any reading above 0.01% of the upstream concentration is a leak.
Exhaust filters that can't be scanned (a hard-ducted exhaust, for example) are checked with a stationary probe downstream instead, against a tighter limit, commonly 0.005%. Record the upstream concentration, the method and the highest penetration found for each filter.
Small leaks in the media can sometimes be repaired within the manufacturer's limits; a damaged filter or a seal leak usually means replacement, followed by recertification.
Site installation assessment
The cabinet is only as good as its connection to the building:
- Type A cabinets with a canopy (thimble) connection: the canopy exhaust alarm must work when exhaust is lost, and the gap must still draw room air.
- Type B cabinets (hard-ducted): the building exhaust must carry the full exhaust load, and the exhaust alarm and blower interlock must work.
- Placement: a cabinet beside a door, under a supply diffuser or in a busy aisle can pass every number and still have its barrier broken by cross-drafts. Note it on the report.
Why cabinets fail
| Symptom | Usual causes |
|---|---|
| Low inflow | Exhaust filter loading, building or canopy exhaust problem on ducted cabinets, blower speed set too low, sash at the wrong height |
| Downflow out of range or uneven | Supply filter loading, a blocked diffuser or grille, damper out of adjustment |
| Smoke escapes at the edges | Low inflow, cross-drafts from doors or diffusers, objects blocking the front grille |
| HEPA leak | Damaged media, failed gasket or seal, filter not seated |
Record readings as found before you adjust anything, then as left after. The as-found data is what tells the lab whether its cabinet was protecting people since the last visit.
What goes on the certificate
The report should name the cabinet, the standard and edition, every reading against its criterion, the instruments and their calibration dates, and your NSF accreditation number. See the full checklist: what a biosafety cabinet certification report should include.
Doing this on every job
Certorum checks each of these as you enter the readings on a phone or tablet: the inflow and downflow averages against the cabinet's own nominal values, downflow uniformity, HEPA penetration and the smoke and alarm results. When you sign off, it produces the certificate and puts the cabinet back on its 12-month cycle.
Certorum does these checks as you type
Enter readings on a phone or tablet on site: each one is checked against the standard and the unit's own set points, and the certificate and invoice are ready when you sign off. Free for up to 40 units.
More guides
- ASHRAE 110 fume hood testing: procedure, ratings and acceptance criteria
- Biosafety cabinet classes and types explained
- What a biosafety cabinet certification report should include
- How often do biosafety cabinets, fume hoods and cleanrooms need certification?
- Cleanroom air changes per hour: how to calculate and verify them
- ISO 14644-1:2015 cleanroom classification: class limits, sample locations and sample volume
- USP <797> cleanroom certification: what's tested every six months
- Handbook 44 scale test procedures
- NIST Handbook 44 scale tolerances explained
- Placed-in-service reports for scales
- Test weights for scale service